Permanent Magnetspannplatte SPNEO

The permanent magnetic clamping plate SPEF is a high precision plate for use on eroding machines and everywhere where the magnetic field should only be directly on the plate. Magnetic chuck SPEF works with a strong, scatter-resistant ceramic-magnetic system, which creates a field height below 3mm. The clamping force can be changed stagelessly in 2 sectors, the plate is silver brazed and therefore very robust and stiffy. The clamping plate is operated by a removeable Allen key. Finish: - Ceramic-magnetic system - Aluminium body - Pole pitch 2 + 1.5 + 6 mm - Nominal holding force 70 N/cm² - Magnetic field height 2-3 mm - Pole plate wearing limit 5 mm

Permanent magnetic clamping plates SPMT with reduced height. The magnetic clamping plate is suitable for wire-eroding, spark eroding and grinding of thin and small workpieces. Finish: - Pole pitch 0.5+1.5 mm - Highest clamping force up to 120 N/cm² - Reduced height with activiation from top surface - Suitable for adaption on zero-point-clamping systems - Low flux depth of 6mm and no residual magnetism - EDM can be performed close to surface without magnetic interference

The magnetic clamping plate SPNM INOX is made of corrosion-resistant special steel and is used for work under corrosive Atmospheres or in corrosive substances. Because of the fine pole pitch and the flat magnetic field, no stray magnetic fields are disturbing the process of machining. Finish: - Neodym-magnetic system - VA body - Pole pitch 1.4 + 0.5 mm - Nominal holding force 60 N/cm² - Magnetic field height 5 mm - Pole plate wearing limit 3 mm

The Permanent magnetic clamping plate SPNM-W has the same magnetic characteristics as clamping chuck SPNM but can be used for horizontal and vertical clamping. SPNM-W are used for the grinding of edges on plates, for grinding angles on plates or for wirecutting. For the use on surface grinding machines, the SPNM-W can be clamped on the electric clamping plate of the machine. Finish: - Neodym-magnet system - Steel body - Pole pitch 1.4+0.5mm - Nominal holding force 100 N/cm² - Magnetic field height 5mm - Pole plate wearing limit 6mm

The Permanent magnetic clamping plate type SPNS is a special type of the high precision magnetic chuck SPNM. ON-OFF switching from above. The hight is reduced to a minimum of 35 mm. The chuck is used where a thin and light design is important or if there is not enough room to switch from the side. The low magnetic field with high induction lines prevents the magnetization of the machining tools. The clamping plate is operated by a removable Allen key. Finish: - Neodym-magnetic system - Steel body - Pole pitch 1.4 + 0.5 mm - Nominal holding force 100 N/cm² - Magnetic field height 5 mm - Pole plate wearing limit 6 mm

Permanent magnetic clamping plate type SPSF, designed for EDM and grinding of small and thin components. With very low height and low weight, the plate can also be placed uppon palletizing systems. The low magnetic field prevents the magnetization of the machining tools. The clamping plate is operated by a removable Allen key. Finish: - Neodym-magnet system - Steel body - Pole pitch 1.5 + 0.8 mm - Nominal holding force 80 N/cm² - Magnetic field height 6 mm - Pole plate wearing limit 5 mm

Permanent magnetic clamping plate SPNM is a high precision magnetic plate to clamp small and thin workpieces for precision grinding and EDM. The low magnetic field prevents the magnetization of the machining tools. The clamping plate is operated by a removeable Allen key. Finish: - Neodym-magnetic system - Steel body - Pole pitch 1.4 + 0.5 mm - Nominal holding force 100 N/cm² - Magnetic field height 5 mm - Pole plate wearing limit 6 mm