524,043 miembros *
2,995 online*
Regístrese aquí GRATIS
Iniciar sesión Registrarse
DMG MORI

Contacto

DMG MORI Global Marketing GmbH
Walter-Gropius-Str.7
80807 München
Alemania
+49 (0) 89 / 24 88 359 00
+49 (0) 89 / 24 88 359 02

Planeador de ruta

Planeador de ruta

DMP 70 (Reference-Nr. 051010)

Precio a petición


  • Número de referencia 051010
    Fabricación 2019
    Horas en funcionamiento Sin resultados
  • Metal working machine
  • Machining centres
  • Machining Centers (Vertical)
  • DMG MORI
  • Siemens

  • General
    High dynamic Vertical Drill-Tap centre with best milling performance; Control: 3D-control Siemens 840D sl Operate
    Working area 1
    Longitudinal 700 mm
    Cross 420 mm
    Vertical 380 mm
    Technical Data
    Feed rate longitudinal/transverse/vertical 60000/60000/60000 mm/min
    Rapid traverse longitudinal/transverse/vertical 60/60/60 m/min

  • Spindle speed 24,000 rpm Spindle 24,000rpm with tool taper ISO 7388-2 - J30 BT30 / BBT 30 (BIG PLUS) possible for pull-studs ISO 7388-3 - JD30 (MAS 403-45°) at spindlespeed higher than 20.000 rpm BBT 30 (BIG PLUS) stipulated! AC-Motor 20 / 4 KW (max. / 100% ED) Watercooling Spin
    Integrated swivel rotary table simultaneous Integated swivel rotary table 5-Axis simultaneous mode! Torque drives incl. direct measuring in A- and C-Axis Swivel range A-Axis -120 / + 100 degrees Max. load C-axis 100kg Table diameter C-Axis d290mm Rotary joint, 4-channels Inclusive Software package
    Tool magazine 25 places Tool magazine 25 places (suitable for inclusion in the tool spindle) Chip-to-chip time 1.6 sec
    Air blast through spindle centre Air blast through spindle center via M-Command; maintained air with small Oil portion Due to needed lead through in main spindle only with swarf removal package ICS possible!
    Oil and emulsion mist separator Oil- and emulsion mist separator Mechanical
    Blum Efficiency package Blum Efficiency package suitable to milling spindle including: Touchprobe TC-52 Infrared Z-Nano cable connected, probe head mechanical for tool break control and length measuring Calibration bar with tool taper Messzyklen
    3D Quick SET 3D quickSET Tool kit for control and compensation of the cinematic accuracy of 5 axis machine configurations (only with option touch probe)
    Signal lamp 4-colour Signal lamp, 4 colours
    DMG MORI Interface PROFIBUS Right DMG MORI Interface PROFIBUS loading door at right machine side PROFIBUS communication between robot and machine for loading cycle 2 channel safety circuits Only in combination with an additional clamping method option!.
    Manual control panel Electrical handwheel
    10 free M-functions for Siemens Free M-Codes (M180-M189) for Siemens 840D potential-free on contacts inside electrical cabinet
    Safety package for power failure Safety package for power failure Overload limiter, Undervoltage moni- toring with fast deceleration control
    Tropical package Package for tropical climate for ambient temperature max. 50°Celsius: includes active cooling for electrical cabinet, active cooling main spindle drive / motor spindle
    IoTconnector DMG MORI IoTconnector The IoTconnector allows the use of online services of DMG MORI (e.g. NETSERVICE or MESSENGER on ADAMOS)
    NETservice DMG MORI NETSERVICE Qualified support by Internet-based remote diagnostics
    Special equipment Clamping pneumatic 1-circuit Including 2x 3/2 way valve pneumatic support control for a clamping point
    Special equipment Lehmann UMT ICS system integrated on the back of the machine suitable for cutting oil Motorex Swisscut Ortho NF-X 15 - IKZ-PB 40bar filter 50µm - Chip conveyor for fine Aluminum Chips - Special feed outer cutting oil feed 281 / min - Workspace and bed
    Special equipment - Frequency 50 Hz - Flow monitors at IKZ and external coolant supply (M7 / M8) - Diagnostic gateway Murr Cube - Auto shut down

  • Spindle speed 24,000 rpm Spindle 24,000rpm with tool taper ISO 7388-2 - J30 BT30 / BBT 30 (BIG PLUS) possible for pull-studs ISO 7388-3 - JD30 (MAS 403-45°) at spindlespeed higher than 20.000 rpm BBT 30 (BIG PLUS) stipulated! AC-Motor 20 / 4 KW (max. / 100% ED) Watercooling Spin
    Integrated swivel rotary table simultaneous Integated swivel rotary table 5-Axis simultaneous mode! Torque drives incl. direct measuring in A- and C-Axis Swivel range A-Axis -120 / + 100 degrees Max. load C-axis 100kg Table diameter C-Axis d290mm Rotary joint, 4-channels Inclusive Software package
    Tool magazine 25 places Tool magazine 25 places (suitable for inclusion in the tool spindle) Chip-to-chip time 1.6 sec
    Air blast through spindle centre Air blast through spindle center via M-Command; maintained air with small Oil portion Due to needed lead through in main spindle only with swarf removal package ICS possible!
    Oil and emulsion mist separator Oil- and emulsion mist separator Mechanical
    Blum Efficiency package Blum Efficiency package suitable to milling spindle including: Touchprobe TC-52 Infrared Z-Nano cable connected, probe head mechanical for tool break control and length measuring Calibration bar with tool taper Messzyklen
    3D Quick SET 3D quickSET Tool kit for control and compensation of the cinematic accuracy of 5 axis machine configurations (only with option touch probe)
    Signal lamp 4-colour Signal lamp, 4 colours
    DMG MORI Interface PROFIBUS Right DMG MORI Interface PROFIBUS loading door at right machine side PROFIBUS communication between robot and machine for loading cycle 2 channel safety circuits Only in combination with an additional clamping method option!.
    Manual control panel Electrical handwheel
    10 free M-functions for Siemens Free M-Codes (M180-M189) for Siemens 840D potential-free on contacts inside electrical cabinet
    Safety package for power failure Safety package for power failure Overload limiter, Undervoltage moni- toring with fast deceleration control
    Tropical package Package for tropical climate for ambient temperature max. 50°Celsius: includes active cooling for electrical cabinet, active cooling main spindle drive / motor spindle
    IoTconnector DMG MORI IoTconnector The IoTconnector allows the use of online services of DMG MORI (e.g. NETSERVICE or MESSENGER on ADAMOS)
    NETservice DMG MORI NETSERVICE Qualified support by Internet-based remote diagnostics
    Special equipment Clamping pneumatic 1-circuit Including 2x 3/2 way valve pneumatic support control for a clamping point
    Special equipment Lehmann UMT ICS system integrated on the back of the machine suitable for cutting oil Motorex Swisscut Ortho NF-X 15 - IKZ-PB 40bar filter 50µm - Chip conveyor for fine Aluminum Chips - Special feed outer cutting oil feed 281 / min - Workspace and bed
    Special equipment - Frequency 50 Hz - Flow monitors at IKZ and external coolant supply (M7 / M8) - Diagnostic gateway Murr Cube - Auto shut down

Enviar pregunta

Más máquinas de DMG MORI Global Marketing GmbH